brazerzkidaiphotos.blogg.se - Cimc raid monitor solarwinds

#Cimc raid monitor solarwinds how to#
#Cimc raid monitor solarwinds install#
#Cimc raid monitor solarwinds software#
#Cimc raid monitor solarwinds professional#

However, it is not a bad BBU.īBUs can be monitored with CIMC, MegaCLI utility, and LSI Mega RAID Storage Manager (MSM). Note: Below 48 hours + disabled the cache mode.

These two values must be above 675 mAh.

Missing: Also suspect that no BBU is present.

Unknown: The status of the BBU is unknown, so a physical inspection is needed.

Here is what you check for in the command output: Here is an example that uses the MegaCLI command utility in order to pull BBU information: MegaCli]#. If your network is live, make sure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment.

#Cimc raid monitor solarwinds software#

This document is not restricted to specific software and hardware versions. Avago LSI Redundant Array of Independent Disks (RAID) controllers.Internet Small Computer Systems Interface (iSCSI).See the Introduction to LSI's MegaCLI Utility article for the download link.Ĭisco recommends that you have knowledge of these topics:

#Cimc raid monitor solarwinds install#

In order to run the Avago LSI MegaCLI commands, you must first download and install the MegaCLI utility. Both the Cisco Integrated Management Controller (CIMC) CLI and the Avago LSI CLI are used in this document.

#Cimc raid monitor solarwinds how to#

See Add nodes for devices connected to UCS controllers to the SolarWinds Platform for details.This document describes how to monitor and replace the Backup Battery Unit (BBU) in both the Unified Computing System (UCS) B and UCS C Series servers. Double-click child UCS devices in the Overview widget and begin managing them as nodes to monitor a UCS cluster in the SolarWinds Platform.

Review your information, and click OK, Add Node.Īfter adding a node for the parent UCS controller, navigate to its Node Details page and click the Hardware icon in the left menu to access the Hardware subview. On the Choose Resources page, select the resources and statistics you want to monitor, and then click Next.Īdvance to the Add Pollers and Change Properties pages to add relevant pollers and adjust node properties. If you have trouble with the User Name, try prepending it with "ucs-".Ĭlick Test to verify credentials, and then click Next. Provide UCS credentials information, including the port on which the UCS Manager listens: Select the UCS Manager Credentials check box. To gather maximum UCS data, select Most Devices: SNMP and ICMP as the Polling Method. Select an ICMP polling method and provide credentials. On the Add Node page, provide the IP Address, or provide the host name and select Dynamic IP Address.

Log into the SolarWinds Platform Web Console as an administrator.Ĭlick Settings > Manage Nodes, and then click Add Node. To add a node to monitor a parent UCS controller in the SolarWinds Platform: Review UCS monitoring requirements before adding nodes. Afterward, you can add connected UCS devices, such as fiber interconnects, chassis, rack servers, and blade servers, to create a UCS cluster. To gain an overview of all information provided by UCS, add the parent UCS controller to the SolarWinds Platform database. This SolarWinds Platform topic applies only to the following products:

View All Application Management Products.

View All IT Service Management Products.

Customer Success with the SolarWinds Support Community.

Installing Server & Application Monitor.

How to Install NPM and Other Orion Platform Products.

Upgrading From the Orion Platform 2016.1 to 2019.4.

Upgrading Your Orion Platform Deployment Using Microsoft Azure.

Upgrading Isn't as Daunting as You May Think.

#Cimc raid monitor solarwinds professional#

SolarWinds Certified Professional Program.